P0122: Throttle/Pedal Position Sensor/Switch 'A' Circuit Low

P0122 means the engine computer is seeing a very low signal from the throttle or accelerator pedal position sensor circuit. The most common fix is replacing a bad throttle body or pedal position sensor and repairing the wiring, usually costing about $150 to $600.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$80 – $900

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0122 mean?

The throttle or accelerator pedal position sensor tells the computer how far you are pressing the gas pedal or opening the throttle. The computer uses that signal to control fuel delivery and throttle response. When the signal is too low, the computer may think the pedal is barely pressed or stuck, so it can limit engine power or set a fault. This can happen from a bad sensor, damaged wiring, corrosion, or a problem inside the throttle body on drive-by-wire cars.

Common symptoms

  • Check engine light on
  • Slow or unresponsive acceleration
  • Engine may go into limp mode
  • Rough idle or stalling
  • Poor fuel economy
  • Reduced engine power warning

Causes, fixes and costs

DashClue diagnosis

P0122: Throttle/Pedal Position Sensor/Switch 'A' Circuit Low

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The car may run in reduced-power mode or stall, which can make merging and passing unsafe. Stop driving if the engine loses throttle response, enters limp mode badly, or stalls repeatedly.

Most likely causes

  1. 1

    Failed throttle position sensor or pedal position sensorHigh

    A dead spot, delayed response, or constant low reading from the pedal or throttle sensor often sets this code. If the light came on with poor acceleration but no wiring damage, this is the most likely cause.

    Quick check: Scan live data and watch the throttle or pedal percentage while slowly pressing the pedal; it should rise smoothly without dropping out.

  2. 2

    Broken, shorted, or corroded wiring connectorHigh

    Intermittent symptoms, a code that returns after bumps, or a code paired with other sensor faults often point to wiring issues. Damaged harnesses near the throttle body or pedal are common.

    Quick check: Inspect the connector and wiring for looseness, corrosion, rubbed-through insulation, or bent pins.

  3. 3

    Dirty or failing electronic throttle bodyMedium

    On many drive-by-wire vehicles, a throttle body that sticks or has a bad internal sensor can create a low-signal complaint. This is more likely if the idle is unstable or the engine stays in limp mode.

    Quick check: Look for heavy carbon buildup in the throttle bore and compare commanded throttle to actual throttle on a scan tool.

  4. 4

    Low reference voltage or PCM problemLow

    If the signal and wiring test good but the code keeps returning, the computer’s reference voltage or internal circuit may be at fault. This is less common than a sensor or wiring issue.

    Quick check: Have a shop test the 5-volt reference and circuit integrity before replacing the PCM.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. A careful DIYer can inspect the connector, wiring, and throttle body, and sometimes replace the pedal sensor or throttle body. You will need a scan tool that shows live data, basic hand tools, and the correct replacement part for your exact vehicle.

Show the steps
  1. Read all stored codes and freeze-frame data
  2. Inspect the throttle body and pedal connector for damage or corrosion
  3. Check live data for a smooth throttle or pedal signal
  4. Clean the throttle body only if the manufacturer allows it
  5. Repair damaged wiring or replace the faulty sensor or throttle body
  6. Clear codes and verify the signal returns to normal
  7. Road test to confirm the light stays off

Estimated repair cost

$120 – $350

Throttle position sensor or accelerator pedal position sensor: parts about $40-$180, labor about $80-$170

  • Electronic throttle body$250 – $650
  • Wiring repair or connector replacement$100 – $300
  • Throttle body cleaning and throttle relearn$80 – $180
  • PCM diagnosis or replacement$250 – $900

Prices vary by vehicle, engine layout, and local labor rates.

Frequently asked questions

Can I drive with P0122?

Usually yes for a short time, but drive gently. If the car goes into reduced-power mode, stalls, or barely responds to the pedal, stop driving and have it towed.

Will P0122 cause limp mode?

Yes, it often can. The computer may limit throttle opening to protect the engine and keep the car from accelerating unexpectedly.

Can a dirty throttle body cause P0122?

Sometimes, especially on drive-by-wire systems where carbon buildup makes the throttle plate stick. It is not the first thing I would assume, but it is worth checking if the throttle body is dirty.

How much does it cost to fix P0122?

Typical independent-shop cost is about $150 to $600, depending on whether the fix is wiring, a pedal sensor, or the throttle body. PCM-related repairs can cost more.

Will P0122 fail an emissions test?

In most states, yes, because the check engine light is on and the readiness monitors may not be set. The code should be repaired and cleared before inspection.

Related codes

  • P0120 Throttle/Pedal Position Sensor/Switch 'A' Circuit
  • P0121 Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance
  • P0123 Throttle/Pedal Position Sensor/Switch 'A' Circuit High
  • P0220 Throttle/Pedal Position Sensor/Switch 'B' Circuit

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.