P0160: O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
P0160 means the engine computer is not seeing the rear oxygen sensor on bank 2 switch as it should, so it cannot properly monitor catalyst efficiency. The most common fix is replacing a bad Bank 2 Sensor 2 O2 sensor, usually about $150 to $350 at an independent shop.
- Severity
- Low
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $100 – $2,500
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0160 mean?
This code points to the downstream oxygen sensor on bank 2, which is the side of the engine opposite cylinder 1 and is usually the sensor after the catalytic converter. That sensor helps the computer confirm the catalytic converter is working and that the exhaust mixture is being cleaned up correctly. When the sensor shows no activity, the computer sees a flat or stuck signal instead of the normal changing voltage. The problem can be the sensor itself, damaged wiring, a bad connector, exhaust leaks, or less commonly a converter issue that changes the exhaust flow the sensor sees.
Common symptoms
- Check engine light on
- Possible bad fuel economy
- May fail emissions test
- Usually no driveability change
- Possible stored catalyst-related codes
- Rough idle if another problem is present
Causes, fixes and costs
P0160: O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
General guide for most cars. Your car may differ.
This code usually does not cause a sudden breakdown, but it can hide a catalyst or fuel-trim problem and may lead to failed emissions testing. Stop driving if the car starts running badly, stalls, or you smell a strong exhaust leak.
Most likely causes
- 1
Faulty Bank 2 Sensor 2 O2 sensorHigh
A dead or slow rear sensor is the most common reason the scan tool shows a flat signal and the check engine light stays on. This fits if the code returns after clearing and there are no obvious wiring or exhaust damage signs.
Quick check: Watch the sensor data on a scan tool; the Bank 2 Sensor 2 voltage should change once the engine is warm. If it stays fixed, unplugged, or obviously lazy compared with the other O2 sensors, the sensor is suspect.
- 2
Wiring or connector problemMedium
Heat near the exhaust can melt wiring, corrode the connector, or break the sensor circuit, which makes the computer read no activity. This is more likely if the code appeared after exhaust work, road damage, or you find a damaged harness near the converter.
Quick check: Inspect the sensor wiring from the sensor to the harness for melted insulation, corrosion, loose pins, or a connector that is not fully latched.
- 3
Exhaust leak near the sensorMedium
A leak upstream of or around the rear sensor can let outside air into the exhaust stream and confuse the reading, especially if the code came with other exhaust-related complaints. You may hear a ticking or hissing sound and see soot marks.
Quick check: Look for soot, broken joints, loose clamps, or noisy leaks around the exhaust pipe and converter area.
- 4
Catalytic converter or engine issue affecting exhaust flowLow
A failing converter or an engine that is not running right can change exhaust oxygen content enough to make the rear sensor look abnormal. This is more likely if P0160 comes with catalyst efficiency codes, misfires, or fuel-trim codes.
Quick check: Scan for related codes and check live data for misfires or fuel-trim problems before replacing the sensor again.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. If the sensor is easy to reach, a careful DIYer can replace it with the correct O2 sensor socket and basic hand tools. If the wiring is damaged or the sensor is seized in the exhaust, ask the shop to diagnose the circuit and inspect for leaks first.
Show the stepsHide the steps
- Verify the code and check for related codes
- Inspect the Bank 2 Sensor 2 wiring and connector
- Check for exhaust leaks near the rear sensor
- Remove the old sensor with an O2 sensor socket
- Install the correct replacement sensor and route the harness away from heat
- Clear the code and road test the vehicle
- Recheck live data to confirm the sensor is switching normally
Estimated repair cost
$150 – $350
Bank 2 Sensor 2 oxygen sensor replacement: parts about $50-$150, labor about $100-$200
- O2 sensor wiring repair$120 – $300
- Exhaust leak repair near rear sensor$100 – $400
- Catalytic converter replacement$900 – $2,500
- Engine tune-up or misfire repair$150 – $800
Prices vary by vehicle, rust level, engine layout, and local labor rates.
Frequently asked questions
Can I drive with code P0160?
Usually yes, but drive with caution. The car will often run normally, but the check engine light will stay on and you may not pass an emissions test.
Will P0160 clear itself?
Sometimes it may disappear if the fault was temporary, but a true sensor or wiring problem usually comes back. If it returns after a few drive cycles, the problem is still there.
Is P0160 the same as a bad catalytic converter?
No. P0160 is about the rear oxygen sensor circuit not showing activity, while catalyst codes like P0420 or P0430 point more directly to converter efficiency, though one problem can affect the other.
Can I replace the oxygen sensor myself?
Often yes if you can safely reach it and the exhaust parts are not rusted solid. You still need to inspect the wiring and make sure you buy the correct Bank 2 Sensor 2 sensor.
Will this code fail emissions testing?
Very likely, because the check engine light is on and the monitor for the catalytic system may not run correctly. Clear the code and fix the cause before inspection.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.