P0222: Throttle/Pedal Position Sensor/Switch 'B' Circuit Low
P0222 means the engine computer is seeing a lower-than-expected voltage signal from throttle or accelerator pedal position sensor circuit B. The most common fix is repairing a damaged connector or wiring, or replacing the throttle body or pedal sensor if it has failed, typically costing $150 to $550 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $100 – $700
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0222 mean?
This code points to a problem in the electronic throttle control system, which tells the engine computer how far you are pressing the gas pedal or opening the throttle plate. Circuit B is one of the redundant signals the computer compares for safety, so if that signal reads too low, it sets P0222. The issue can come from a bad sensor, damaged wiring, corrosion in the connector, or a throttle body problem. In many cars, the computer will limit engine power to protect the drivetrain.
Common symptoms
- Check engine light on
- Reduced engine power
- Poor throttle response
- Car hesitates when accelerating
- Limp mode or limited speed
- Rough idle or stalling
Causes, fixes and costs
P0222: Throttle/Pedal Position Sensor/Switch 'B' Circuit Low
General guide for most cars. Your car may differ.
If ignored, the vehicle may stay in reduced-power mode, hesitate badly, or stall when you need acceleration. Stop driving if the engine dies, the throttle response becomes erratic, or the car will not maintain a steady idle.
Most likely causes
- 1
Damaged wiring or loose connectorHigh
Intermittent throttle response, limp mode, or a code that returns after bumps or rain often points to a wiring or connector issue. Corrosion, broken wires, or a loose plug can pull the signal voltage too low.
Quick check: Inspect the throttle body or pedal sensor connector for bent pins, green corrosion, water intrusion, or loose fit. Wiggle-test the harness while watching for a change in idle or scan-tool data.
- 2
Failed throttle position sensor or accelerator pedal sensorHigh
A steady low-voltage reading, poor response, or no change in scan data as the pedal is moved points to a failed sensor inside the throttle body or pedal assembly. If one signal is bad while the other tracks normally, the sensor is a strong suspect.
Quick check: Use a scan tool to watch throttle and pedal position data. The readings should change smoothly; if circuit B stays stuck low or drops out, the sensor is likely faulty.
- 3
Dirty or sticking electronic throttle bodyMedium
Carbon buildup can make the throttle plate stick and confuse the sensor readings, especially if the car idles poorly or goes into reduced power during acceleration. This is more likely if the throttle body has heavy deposits and no wiring damage is found.
Quick check: Remove the intake duct and inspect the throttle plate for heavy carbon or sticking. If cleaning restores normal operation, the throttle body was part of the problem.
- 4
Power, ground, or PCM issueLow
If multiple throttle-related codes are present or the sensor tests good, a missing 5-volt reference, bad ground, or rare control-module fault may be lowering the circuit signal. This is more likely when the problem affects more than one sensor.
Quick check: Verify reference voltage and ground at the sensor connector with a multimeter, and check for additional related codes before replacing parts.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. Basic inspection and cleaning are possible at home with a scan tool, multimeter, and throttle-body cleaner, but electrical testing is often needed to avoid replacing the wrong part. If the wiring and connectors look good, ask the shop to test the throttle body, pedal sensor, 5-volt reference, and ground circuits.
Show the stepsHide the steps
- Check for other throttle or pedal sensor codes
- Inspect connectors and wiring for damage or corrosion
- Clear the code and test drive to see if it returns
- Watch live data for throttle/pedal sensor movement
- Clean the throttle body if it is dirty and accessible
- Test reference voltage and ground with a multimeter
- Replace the faulty sensor, pedal assembly, or throttle body if confirmed
Estimated repair cost
$150 – $350
Repair throttle or pedal sensor wiring/connector: diagnosis plus minor harness repair
- Clean electronic throttle body$100 – $180
- Replace accelerator pedal position sensor assembly$180 – $400
- Replace throttle body assembly$300 – $700
- Diagnose and repair PCM power/ground fault$150 – $500
Prices vary by vehicle, labor rate, and whether the sensor is built into the throttle body or pedal assembly.
Frequently asked questions
Can I drive with code P0222?
Usually yes for a short time, but only with caution. If the car is stuck in limp mode, stalls, or responds unpredictably to the pedal, do not keep driving it.
Will P0222 clear itself?
Sometimes it may disappear if the connection was momentary, but the underlying fault usually comes back. If the code returns, the problem needs diagnosis.
Can I fix P0222 myself?
You may be able to inspect the wiring, clean the throttle body, and check connectors yourself. If electrical testing is needed, it is better handled by a shop.
Is P0222 a throttle body problem or a pedal problem?
It can be either one, because the code only tells you circuit B is reading low. Live data and electrical tests are the fastest way to tell which part failed.
Will P0222 cause an inspection failure?
In many states, yes, because the check engine light is on and the emissions system is not ready. A stored or pending throttle control code can also affect driveability.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.