P0106: Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance

P0106 means the engine computer is seeing a manifold absolute pressure (MAP) or barometric pressure signal that does not match normal engine load or key-on air pressure. The most common fix is to replace a bad MAP sensor or repair the vacuum hose/wiring to it, usually about $120 to $350 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$100 – $450

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0106 mean?

The MAP sensor helps the engine computer figure out how much air is entering the engine so it can set fuel and ignition timing correctly. On some cars, the same code can also point to a barometric pressure input problem. This code sets when the signal is present but seems implausible, such as reading too high, too low, or changing in a way that does not fit engine conditions. Vacuum leaks, a dirty throttle body, engine performance problems, or wiring faults can all make the reading look wrong.

Common symptoms

  • Check engine light on
  • Rough idle
  • Hesitation on acceleration
  • Loss of power
  • Poor fuel economy
  • Hard starting

Causes, fixes and costs

DashClue diagnosis

P0106: Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The car may still run, but it can run rich or lean and lose power or use extra fuel. Stop driving if it stalls, runs extremely rough, or the check engine light starts flashing.

Most likely causes

  1. 1

    Faulty MAP sensorHigh

    A bad sensor often causes a steady rough idle, hesitation, or poor fuel economy with no obvious mechanical problem. If the code returns quickly after clearing and the wiring looks okay, the sensor is a top suspect.

    Quick check: Read MAP data with a scan tool and compare it to key-on engine-off barometric pressure and to engine vacuum at idle.

  2. 2

    Vacuum leak or intake air leakHigh

    Extra unmetered air can make the MAP reading and engine load calculation disagree, often causing rough idle or hesitation. Hissing sounds, high idle, or fuel trim codes support this cause.

    Quick check: Inspect vacuum hoses, intake boots, and the PCV system for cracks or loose fittings; a smoke test is best.

  3. 3

    Wiring or connector problem at MAP sensorMedium

    Intermittent signal loss or an unstable reading can set a range/performance code, especially if the light comes and goes. Corrosion, broken wires, or a loose connector are more likely if the problem is intermittent over bumps or in wet weather.

    Quick check: Wiggle-test the harness and inspect the connector for bent pins, corrosion, or damaged insulation.

  4. 4

    Engine performance problem affecting vacuumLow

    A clogged throttle body, restricted exhaust, or an engine that does not make normal vacuum can confuse the MAP signal. This is more likely if the car has multiple drivability symptoms beyond the code.

    Quick check: Compare idle vacuum and scan data with a known-good baseline; inspect the throttle body and engine air intake first.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. A careful DIYer can inspect hoses, connectors, and sometimes replace the MAP sensor with basic hand tools. You will need a scan tool to confirm the reading; if vacuum tests or wiring diagnosis are needed, ask the mechanic for MAP data checks, a smoke test, and harness inspection.

Show the steps
  1. Read all codes and freeze-frame data
  2. Inspect the MAP sensor connector and wiring
  3. Check vacuum hoses and intake ducting for leaks
  4. Look for a damaged or dirty MAP sensor port
  5. Compare MAP readings key on, engine off, and at idle
  6. Clear the code and road test
  7. Replace the MAP sensor if readings stay out of range
  8. Recheck for returning codes

Estimated repair cost

$120 – $350

MAP sensor replacement: parts ~$30-$150, labor ~$90-$200

  • Repair vacuum leak or intake hose$100 – $450
  • MAP sensor wiring or connector repair$100 – $300
  • Throttle body cleaning or service$100 – $250
  • Engine intake smoke test and diagnosis$120 – $220

Prices vary by vehicle, engine layout, and local labor rates.

Frequently asked questions

Can I drive with code P0106?

Usually yes for a short time, but drive gently and get it checked soon. If the engine stalls, runs very rough, or loses a lot of power, stop driving.

Will P0106 clear itself?

It may go away for a while if the fault is intermittent, but the underlying problem usually comes back. Clearing the code without fixing the cause normally does not solve it.

Is P0106 always a bad MAP sensor?

No. A vacuum leak, bad wiring, dirty throttle body, or other engine air problem can cause the same code. The sensor is common, but it should not be replaced without testing.

Can a dirty air filter cause P0106?

A dirty air filter usually does not cause this code by itself, but intake restrictions or airflow problems can contribute. The MAP sensor signal and vacuum readings matter more than the filter alone.

Will P0106 fail emissions inspection?

In many states, yes, because the check engine light is on and the system has a stored fault. Even if the car runs okay, the code usually needs to be fixed and cleared before inspection.

Related codes

  • P0100 Mass Or Volume Air Flow Circuit
  • P0101 Mass or Volume Air Flow Circuit Range/Performance
  • P0102 Mass or Volume Air Flow Circuit Low Input
  • P0103 Mass Or Volume Air Flow Circuit High Input
  • P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
  • P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.