P0108: Manifold Absolute Pressure/Barometric Pressure Circuit High Input
P0108 means the engine computer is seeing a MAP or barometric pressure signal that is higher than expected, which can throw off fuel and timing calculations. The most common fix is replacing a faulty MAP sensor, cleaning a bad connector, or repairing wiring, usually costing about $150 to $400 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $120 – $700
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0108 mean?
The MAP sensor tells the engine computer how much pressure is in the intake manifold so it can calculate engine load. On some vehicles, the barometric pressure reading is combined with this circuit, so a bad signal can affect how the computer measures air pressure outside the engine too. When the voltage stays too high, the computer thinks the engine is under a different load than it really is. That can cause rich running, rough idle, hard starting, or poor acceleration.
Common symptoms
- Check engine light on
- Rough idle
- Hesitation when accelerating
- Hard starting
- Poor fuel economy
- Black smoke from exhaust
Causes, fixes and costs
P0108: Manifold Absolute Pressure/Barometric Pressure Circuit High Input
General guide for most cars. Your car may differ.
The car may keep running, but the wrong pressure signal can cause poor fuel control, stalling, or flooding on some engines. Stop driving if the engine runs extremely rough, stalls repeatedly, or the check engine light starts flashing.
Most likely causes
- 1
Faulty MAP sensorHigh
A bad sensor often causes a constant high reading, along with rough idle, hesitation, or a hard-start condition. If the code returns quickly after clearing it, the sensor is a top suspect.
Quick check: With a scan tool, compare MAP voltage or pressure to key-on engine-off barometric pressure; if it is way off or stuck high, the sensor is likely bad.
- 2
Damaged wiring or poor connector at the MAP sensorHigh
A rubbed-through wire, loose plug, corrosion, or 5-volt reference problem can push the signal voltage too high. Intermittent symptoms or the code changing when you wiggle the harness point to this.
Quick check: Inspect the connector for bent pins, oil, water, or corrosion, and gently wiggle the harness while watching live data for spikes.
- 3
Vacuum hose or intake problem affecting MAP readingMedium
If the sensor uses a vacuum hose or sits on a cracked intake, the reading can become inaccurate and trigger drivability problems. This is more likely if there is also a lean code, rough idle, or hissing noise.
Quick check: Look for cracked hoses, loose intake ducts, or obvious vacuum leaks around the intake manifold and sensor port.
- 4
Engine control module issue or incorrect reference signalLow
This is less common, but a problem with the ECU, shared sensor reference, or internal circuit can keep the MAP input high even when the sensor is good. It becomes more likely only after the sensor, wiring, and vacuum checks pass.
Quick check: Verify proper 5-volt reference and ground at the sensor; if those are correct and the signal still reads wrong, the module or harness may need deeper testing.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. A basic DIY check only needs a scan tool, flashlight, and inspection tools for the intake and connector. If the wiring, vacuum hoses, and sensor look good, diagnosis can get tricky and a shop may need to test the circuit with a meter and lab data.
Show the stepsHide the steps
- Read and clear the code, then see if it returns right away
- Inspect the MAP sensor connector and wiring for damage or corrosion
- Check the intake tubing and any vacuum hoses for cracks or leaks
- Compare MAP live data with key-on engine-off barometric pressure
- Verify the sensor has proper power and ground
- Replace the MAP sensor if it reads implausibly high and wiring is good
- Retest and confirm the code does not return
Estimated repair cost
$150 – $350
Replace MAP sensor: parts about $40-$150, labor about $110-$200
- Repair MAP wiring or connector$120 – $300
- Smoke test and repair vacuum leak$150 – $450
- Diagnose and repair ECU or shared circuit fault$250 – $700
Prices vary by vehicle, engine layout, and labor rates in your area.
Frequently asked questions
Can I drive with code P0108?
Usually yes for a short time, but drive gently and get it checked soon. If the engine stalls, runs very rough, or the check engine light flashes, stop driving.
What causes a MAP sensor code to read high input?
The most common causes are a bad MAP sensor, damaged wiring or connector, or a vacuum/intake problem affecting the signal. Less often, the engine computer or reference circuit is the issue.
Can I fix P0108 myself?
You may be able to if the problem is a loose connector, cracked hose, or easy sensor replacement. If wiring testing or computer diagnosis is needed, a shop is usually the better choice.
Will P0108 fail an emissions test?
In many states it can fail because the check engine light is on and the readiness monitors may not be set. Even if it passes tailpipe numbers, the stored code is often enough to fail inspection.
Do I need to replace the throttle body for P0108?
Not usually. This code points to the MAP or barometric pressure circuit, so the sensor, wiring, vacuum leaks, or control circuit should be checked first.
Related codes
- P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
- P0113 Intake Air Temperature Sensor 1 Circuit High
- P0106 Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance
- P0101 Mass or Volume Air Flow Circuit Range/Performance
- P0100 Mass Or Volume Air Flow Circuit
- P0121 Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.