P0113: Intake Air Temperature Sensor 1 Circuit High
P0113 means the engine computer is seeing an intake air temperature (IAT) signal that is too high, which usually means the sensor circuit is open, unplugged, or the sensor has failed. The most common fix is repairing the connector or replacing the IAT sensor, typically about $75 to $250 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $75 – $350
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0113 mean?
The intake air temperature sensor tells the engine computer how hot the air entering the engine is. That information helps the computer adjust fuel mixture and timing, especially during cold starts and hot weather. When the circuit reads too high, the computer usually thinks the intake air is extremely cold or the signal is out of range because the circuit is open. This can happen from a bad sensor, damaged wiring, a loose connector, or a problem with the intake tube or air box area where the sensor sits.
Common symptoms
- Check engine light on
- Hard starting when cold
- Rough idle
- Hesitation on acceleration
- Poor fuel economy
- Possible slightly rich or lean running
Causes, fixes and costs
P0113: Intake Air Temperature Sensor 1 Circuit High
General guide for most cars. Your car may differ.
The car usually still runs, but fuel control may be off and cold starts or drivability can get worse. Stop driving if the engine runs very rough, stalls often, or the check engine light starts flashing.
Most likely causes
- 1
Unplugged or loose IAT sensor connectorHigh
A loose connector often causes an immediate P0113, especially if the light came on after air filter, intake, or engine work. The code may come and go if the connection is intermittent.
Quick check: Inspect the sensor plug for looseness, broken tabs, corrosion, or a connector not fully seated.
- 2
Damaged IAT sensor wiring or open circuitHigh
Broken, rubbed-through, or corroded wires can make the signal read too high all the time or only when the engine moves. This is more likely if the code returns after clearing or changes when you wiggle the harness.
Quick check: Look for damaged wiring near the air cleaner, intake tube, or harness routing and gently wiggle-test the harness with the engine off.
- 3
Faulty intake air temperature sensorMedium
A failed sensor can set P0113 even when the connector and wiring look normal. This is common if the engine otherwise runs normally but the code comes back right away.
Quick check: Compare live IAT data to outside air temperature after the car sits overnight; a bad sensor often shows an unrealistic reading.
- 4
Problem in the intake duct or air box areaLow
If the sensor is built into the air intake duct or MAF assembly, cracks, moisture intrusion, or a loose sensor mount can affect the signal. This fits cases where the code started after an intake repair or air filter service.
Quick check: Inspect the intake tube, air box, and sensor mounting for damage, missing seals, or signs of water intrusion.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. You may be able to fix this with basic tools, a flashlight, and contact cleaner if the problem is a loose plug or obvious wiring issue. If the sensor is part of another assembly or the wiring needs testing with a meter, ask the shop to diagnose the IAT circuit and verify the signal and reference voltage.
Show the stepsHide the steps
- Turn the key off and locate the IAT sensor and connector
- Inspect the plug for looseness, corrosion, bent pins, or broken locking tabs
- Check the wiring near the air intake for cuts, rubbing, or oil damage
- Clear the code and see if it returns after a short drive
- If available, view live IAT temperature with a scan tool and compare it to ambient temperature
- Replace the sensor if the reading stays unrealistic and wiring looks good
- Recheck for stored codes after the repair
Estimated repair cost
$75 – $250
IAT sensor replacement: parts usually $20-$80, labor $55-$170
- Connector or wiring repair$120 – $350
- Air intake duct or sensor housing repair$100 – $300
- Diagnostic fee for circuit testing$100 – $180
Prices vary by vehicle, engine layout, and local labor rates.
Frequently asked questions
Can I drive with code P0113?
Usually yes for a short time, but drive gently and get it checked soon. If the engine stalls, runs very rough, or the check engine light flashes, stop driving.
What is the most common fix for P0113?
The most common fix is repairing a loose or damaged IAT sensor connector or replacing the sensor itself. On many cars the part is inexpensive, but wiring damage can raise the cost.
Will P0113 hurt fuel economy?
Yes, it can. When the engine computer gets a bad air temperature signal, it may add or subtract the wrong amount of fuel.
Can I clear P0113 without replacing parts?
Sometimes, if the code was caused by a loose plug or temporary wiring issue. If it comes back, the underlying fault still needs to be repaired.
Will P0113 keep my car from passing inspection?
In many states, yes, because the check engine light is on and the readiness monitors may not complete. The code should be fixed and cleared before inspection.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.