P0112: Intake Air Temperature Sensor 1 Circuit Low

P0112 means the engine computer is seeing an intake air temperature sensor signal that is too low, which usually points to a sensor or wiring problem. The most common fix is replacing the intake air temperature sensor or repairing damaged wiring, typically $100 to $300 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$60 – $400

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0112 mean?

The intake air temperature (IAT) sensor tells the engine computer how warm the air entering the engine is. That information helps the computer adjust fuel delivery and ignition timing for better starting, drivability, and emissions. When the circuit reads too low, the computer thinks the incoming air is much hotter than it really is, or the signal is being pulled down by a wiring fault. This can happen from a failed sensor, corrosion in the connector, or damaged wiring near the air intake.

Common symptoms

  • Check engine light on
  • Rough idle
  • Hard starting
  • Bad gas mileage
  • Hesitation when accelerating
  • Possible rich-running smell

Causes, fixes and costs

DashClue diagnosis

P0112: Intake Air Temperature Sensor 1 Circuit Low

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The car will usually still run, but fuel economy and drivability can suffer, and the engine may run too rich or too lean depending on the failure. Stop driving if the engine starts stalling, runs very rough, or the check engine light begins flashing.

Most likely causes

  1. 1

    Bad intake air temperature sensorHigh

    A failed sensor is the most common cause, especially if the code returns right after clearing and the engine may run poorly or get bad fuel economy.

    Quick check: Inspect the sensor for damage and compare live scan-tool intake air temperature to ambient temperature after the car has sat overnight.

  2. 2

    Corroded or loose connectorMedium

    If the light is intermittent or the problem changes when the harness is moved, a bad connector is likely.

    Quick check: Unplug the sensor and look for bent pins, green corrosion, moisture, or a loose fit.

  3. 3

    Damaged wiring or short to groundMedium

    A rubbed-through wire can hold the signal low all the time, which often causes an immediate code and may affect other intake-related readings.

    Quick check: Inspect the wiring from the sensor to the engine harness for cuts, melted spots, or chafing near the air box and intake tube.

  4. 4

    Problem in the air intake housing or sensor mountingLow

    If the sensor is loose, installed wrong, or contaminated with oil or dirt, the reading can be inaccurate and set the code.

    Quick check: Make sure the sensor is seated correctly and the intake tract is intact and not heavily contaminated.

Can you fix it yourself?

Possible with some experience

Difficulty: Easy. On many cars this is a simple sensor and connector inspection with a basic socket or screwdriver, plus a scan tool if you have one. If wiring repair is needed, it is still possible for a careful DIYer, but you need to trace and test the circuit correctly.

Show the steps
  1. Read the code and freeze-frame data.
  2. Look at live IAT temperature after the engine has cooled overnight; it should be close to outdoor temperature.
  3. Inspect the sensor connector for corrosion, loose pins, or broken lock tabs.
  4. Check the wiring for rubbing, cuts, or melted insulation.
  5. Unplug and reseat the connector, then clear the code and retest.
  6. Replace the IAT sensor if readings are wrong and the wiring looks good.
  7. Repair damaged wiring if the code returns after sensor replacement.

Estimated repair cost

$100 – $300

Intake air temperature sensor replacement: parts about $20-$80, labor about $80-$220

  • Connector or wiring repair$120 – $400
  • Air intake duct or housing repair$60 – $250
  • Diagnosis and electrical testing$100 – $180

Prices vary by vehicle, location, and how hard the sensor and wiring are to access.

Frequently asked questions

Can I drive with code P0112?

Usually yes for a short time, but drive gently and get it checked soon. If the engine starts running very rough, stalling, or the check engine light flashes, stop driving.

What does “circuit low” mean on an IAT sensor code?

It means the computer is seeing a signal voltage that is lower than expected. That is often caused by a bad sensor, a shorted wire, or a poor connection.

Can a dirty air filter cause P0112?

A dirty air filter usually does not cause this code by itself. The problem is more often the sensor, connector, or wiring near the intake.

Will P0112 fail an emissions test?

Yes, it can. A stored check engine light and an active intake air temperature fault can cause an emissions test failure in many states.

Is P0112 expensive to fix?

Usually it is one of the cheaper check-engine codes to fix. Many repairs fall in the $100 to $300 range unless wiring damage is extensive.

Related codes

  • P0110 Intake Air Temperature Sensor 1 Circuit
  • P0111 Intake Air Temperature Sensor 1 Circuit Range/Performance
  • P0113 Intake Air Temperature Sensor 1 Circuit High
  • P0101 Mass or Volume Air Flow Circuit Range/Performance
  • P0171 System Too Lean (Bank 1)
  • P0401 Exhaust Gas Recirculation Flow Insufficient Detected

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.