P0202: Injector Circuit/Open - Cylinder 2

P0202 means the engine computer is not seeing a working electrical circuit for the number 2 fuel injector. The most common fix is repairing wiring or replacing the injector, usually about $150 to $450 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$20 – $1,200

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0202 mean?

This code sets when the engine control module detects an open circuit, high resistance, or no signal in the electrical circuit for cylinder 2’s fuel injector. The injector’s job is to spray fuel into that cylinder at the right time so the engine can run smoothly. If the circuit is broken, the injector may not deliver fuel, or it may work only intermittently. That can cause a misfire, rough running, or a no-start on some vehicles if the problem is severe enough.

Common symptoms

  • Check engine light on
  • Rough idle
  • Engine misfire
  • Hesitation on acceleration
  • Loss of power
  • Bad fuel mileage

Causes, fixes and costs

DashClue diagnosis

P0202: Injector Circuit/Open - Cylinder 2

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The engine may run rough and can damage the catalytic converter if it keeps misfiring. Stop driving if the check engine light starts flashing, the engine stalls, or the car shakes badly under load.

Most likely causes

  1. 1

    Damaged injector wiring or connectorHigh

    Intermittent misfire, rough idle, or the code returning after hitting bumps often points to a broken wire, loose plug, or corrosion at the injector connector.

    Quick check: Inspect the cylinder 2 injector connector and harness for loose pins, green corrosion, rubbed-through insulation, or broken wires. Wiggle-test the harness with the engine idling if safely accessible.

  2. 2

    Failed fuel injectorHigh

    A dead injector can cause a cylinder 2 misfire, rough running, and sometimes a strong fuel smell or no change when the injector is commanded on.

    Quick check: Measure injector resistance and compare it with the other injectors, or listen for a clicking sound with a mechanic’s stethoscope.

  3. 3

    Blown injector fuse or power supply problemMedium

    If the code appeared suddenly and more than one injector or cylinder issue is present, the injector may not be getting battery power at all.

    Quick check: Check injector-related fuses, relays, and the power feed at the injector connector with a test light or multimeter.

  4. 4

    Engine computer driver faultLow

    If wiring and the injector test good but the circuit still does not operate, the ECM may not be grounding the injector properly.

    Quick check: Verify power and control signal at the injector with proper noid light or scope testing before condemning the ECM.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. A careful DIYer can inspect the connector, check fuses, and test injector resistance with a multimeter. If wiring tests are inconclusive or the ECM needs diagnosis, this becomes a shop job.

Show the steps
  1. Turn the key off and inspect the cylinder 2 injector connector.
  2. Look for bent pins, corrosion, loose fit, or damaged wires.
  3. Check related fuses and injector power supply.
  4. Compare injector resistance with the other cylinders.
  5. Clear the code and road test to see if it returns.
  6. If the code comes back, test the harness continuity to the ECM.
  7. Replace the injector or repair the wiring only after testing confirms the fault.

Estimated repair cost

$150 – $350

Repair injector wiring or connector: diagnosis plus pigtail repair or wire repair

  • Replace fuel injector$200 – $450
  • Replace injector fuse or relay$20 – $120
  • ECM driver repair or replacement$400 – $1,200

Prices vary by vehicle, engine layout, and local labor rates.

Frequently asked questions

Can I drive with code P0202?

Usually yes for a short time if the engine only runs a little rough, but drive gently and get it checked soon. If the check engine light flashes or the engine shakes badly, stop driving.

What causes P0202 the most?

The most common causes are a bad injector connector, damaged wiring, or a failed cylinder 2 injector. A blown fuse or ECM problem is less common.

Will P0202 cause a misfire code too?

Often yes. If cylinder 2 is not getting fuel, the engine may also set a misfire code such as P0302.

Can I fix P0202 myself?

You may be able to inspect the connector, check fuses, and test the injector if you have a multimeter. If the wiring repair requires tracing harness damage or ECM testing, a shop is the better choice.

Will P0202 fail an emissions test?

In many states it can fail an inspection if the check engine light is on or the engine is misfiring. Even if it passes readiness checks, the underlying problem should be fixed.

Related codes

  • P0201 Injector Circuit/Open - Cylinder 1
  • P0203 Injector Circuit/Open - Cylinder 3
  • P0302 Cylinder 2 Misfire Detected
  • P0300 Random/Multiple Cylinder Misfire Detected
  • P0171 System Too Lean (Bank 1)

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.