P0203: Injector Circuit/Open - Cylinder 3
P0203 means the engine computer is not seeing a proper electrical signal in the fuel injector circuit for cylinder 3. The most common fix is repairing the wiring, connector, or the injector itself, which usually costs about $150 to $450 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $80 – $1,200
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0203 mean?
The fuel injector for cylinder 3 sprays fuel into that cylinder when the engine computer commands it. With P0203, the circuit is open somewhere, so the injector may not fire at all or may fire intermittently. That can cause a misfire, rough running, and reduced power because cylinder 3 is not getting the fuel it needs. The problem is usually electrical, not a fuel pressure issue.
Common symptoms
- Check engine light on
- Rough idle
- Engine hesitation
- Loss of power
- Poor fuel economy
- Engine may misfire
Causes, fixes and costs
P0203: Injector Circuit/Open - Cylinder 3
General guide for most cars. Your car may differ.
The engine can usually still run, but it may shake, lack power, and get worse if the injector stops working completely. Stop driving if the check engine light starts flashing, the engine runs very rough, or the car stalls.
Most likely causes
- 1
Damaged injector wiring or connectorHigh
This is the most common cause when the code appears with rough idle, hesitation, or an occasional misfire. Vibration, heat, or rodent damage can break the wire or loosen the connector at cylinder 3.
Quick check: Inspect the wiring and plug at injector 3 for broken insulation, bent pins, corrosion, or a loose fit.
- 2
Failed fuel injector on cylinder 3High
A bad injector can have an internal open circuit, which fits a code that points to one cylinder only. It is more likely if the wiring looks fine but the injector does not click or respond during testing.
Quick check: Listen for injector click with a stethoscope or compare resistance with the other injectors.
- 3
Blown injector fuse or relay issueMedium
If more than one injector is affected or the code came on suddenly, power supply to the injector circuit may be interrupted. This can also show up as hard starting or a no-start condition in some cases.
Quick check: Check the injector fuse and related power supply circuits for voltage with the key on.
- 4
PCM driver circuit problemLow
If the wiring and injector test good, the engine computer may not be grounding the injector correctly. This is less common, but it can happen when all other parts of the circuit check out.
Quick check: Have a shop verify injector pulse at the PCM and rule out wiring damage before replacing the computer.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. Basic checks like inspecting the connector, checking for broken wires, and swapping the injector with another cylinder can be DIY-friendly if you are comfortable working around fuel system parts. For electrical testing, you need a multimeter and ideally a scan tool; if the circuit tests are inconclusive, ask the shop to test injector power, ground, and PCM control.
Show the stepsHide the steps
- Scan for related misfire or injector codes.
- Inspect cylinder 3 injector connector and harness.
- Check the injector fuse and related power feed.
- Compare injector resistance to the other cylinders.
- Listen for injector clicking with the engine running.
- Repair damaged wiring or replace the injector if it tests open.
- Clear the code and road test.
- Recheck for return of the code or misfire.
Estimated repair cost
$150 – $350
Repair injector wiring or connector: parts and labor; varies with wiring damage access
- Replace fuel injector on cylinder 3$250 – $600
- Replace injector fuse, relay, or related power supply repair$80 – $200
- PCM driver diagnosis and possible PCM repair/replacement$300 – $1,200
Prices vary by engine layout, parts quality, and local labor rates.
Frequently asked questions
Can I drive with P0203?
Usually yes for a short time, but drive gently and get it checked soon. If the engine starts flashing the check engine light, runs very rough, or stalls, stop driving.
Will P0203 cause a misfire?
Yes. If cylinder 3 injector is not working, that cylinder may misfire or contribute less power, which can make the engine shake or hesitate.
Is P0203 always a bad injector?
No. A broken wire, loose connector, blown fuse, or PCM control issue can cause the same code. The injector itself is only one possible cause.
Can I fix P0203 myself?
You may be able to if the problem is a loose plug, corroded connector, or visibly damaged wiring. If testing is needed or the injector must be replaced, it is better handled with proper tools and fuel system precautions.
Will P0203 clear itself?
It may come and go if the connection is intermittent, but the problem usually does not fix itself. If the fault returns after clearing the code, the circuit still has a defect.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.